SIEMENS ET 200SP AI Energy Meter CT HF 6ES7134-6PA01-0CU0

SIEMENS ET 200SP AI Energy Meter CT HF 6ES7134-6PA01-0CU0 About

Manufacturer SeriesS7 ET 200 CPU Brand Siemens Firmware versionV8.0Model Name/Number6ES7134-6PA21-0CU0STEP 7 TIA Portal configurable/integrated from version STEP 7 V16 or higher with HSP SIMATIC ET 200SP, analog input module, AI Energy Meter CT HF, for 1A or 5A current transformer, with network analysis functions, suitable for BU type U0, channel diagnostics 

General Information

• Product: AI Energy Meter RC HF (Analog Input Module)

• For: Rogowski coils or current/voltage transformer (333 mV)

• BU Type: U0

• Channel diagnostics: Yes

• Firmware Version: V8.0 (FW update possible)

• Color Code: CC20

• Supported Power Systems: TT, TN, IT

Functions

• Voltage, Current, Energy, Frequency, Active/Reactive Power

• Power Factor, Reactive Power Compensation

• Line Analysis: Instantaneous/half-wave values, THD, Harmonics, Voltage Dip/Swell

• I&M Data: I&M0 to I&M3

• Isochronous Mode: No

Engineering / Configuration

• STEP 7 TIA Portal: V16 or higher with HSP

• STEP 7 Classic: V5.5 SP3 or higher

• PROFIBUS GSD: Revision 3 or 5+

• PROFINET GSD: V2.3

• Switching Operating Modes in RUN: Yes (25 user data variants)

• Cyclic & Acyclic Measured Value Access: Yes

• Reparameterization & Calibration in RUN: Yes

Mounting / Supply

• Mounting Position: Any

• Rated Supply Voltage: 24 V DC (19.2 28.8 V DC)

• Current Consumption: 12.5 mA (typ.), 17 mA (max)

• Power Loss: 400 mW

Address Area

• Inputs: 256 bytes

• Outputs: 20 bytes

  Analog Inputs

Analog Inputs

• Cycle Time (all channels): 50 ms

• Cable Length: Shielded/Unshielded max. 200 m

• Sampling Frequency: max. 2048 kHz

• Measuring Procedures: TRMS for Voltage & Current

• Measured Value Acquisition: Seamless

• Bandwidth: 3.2 kHz

• Frequency Measurement Range: 40 70 Hz

Voltage Measurement

• Line-to-neutral: 3 300 V (max 277 V)

• Line-to-line: 6 519 V (max 480 V)

• Internal resistance: 1.5 M

• Power consumption per phase: 60 mW

• Impulse voltage resistance: 2.5 kV

• Overvoltage Category: CAT II (IEC 61010 Part 1)

Current Measurement (Rogowski/I-U Converter)

• Max AC current: 424 mV

• Max continuous voltage: 2 V

• Short-time withstand voltage: 30 V (1 s)

• Input resistance: 120 k

• Zero point suppression: 020% of nominal current

Accuracy (IEC 61557-12)

• Voltage, Current, Neutral Current: 0.2

• Apparent Power, Active Power: 0.5

• Reactive Power: 1

• Power Factor: 0.5

• Active Energy: 0.5

• Reactive Energy: 1

• Phase Angle: 0.5

• Frequency: 0.05

• Harmonics, THDU, THDI: 1

• Line Analysis Accuracy (IEC 61000-4-30): Class S

Potential Separation

• Between channels: No

• Between channels & backplane bus: Yes

• Between channels & load voltage L+: Yes

Isolation

• Channels Backplane Bus (24 V supply): 1920 V AC, 2 s

• Backplane Bus 24 V supply: 707 V DC

Diagnostics / Status

• Alarms: Diagnostic & Limit Value Alarm

• Hardware Interrupt: Yes, up to 16 process values

• Line Quality, Supply Voltage, Module Fault, Parameter Errors: Monitored

• LEDs: PWR, Channel Status (Green), Channel Diagnostics (Red), Module Diagnostics (Green/Red)

Dimensions & Weight

• Width Height Depth: 20 73 58 mm

• Weight: 45 g 

Technical Details